1800 ВТ 0-30MPa high pressure air pump PCP electric air compressor
The setting of the pressure plate can set the pressure you want, and when the pressure reaches the set value, it will stop. This item can save your time and work better.
технические данные:
<улей>
l модель: set the compressor pump in Pressure style
l блок питания:220 В 50 Гц
l мощность: 1.8 KW
l скорость вращения: 2800r / мин
l рабочее давление: 0-30mpa / 0-300BAR / 0-4500psi
l система смазки:splash type
l режим сжатия: two stage compression
l режим охлаждения: водяное охлаждение
l вес:15.8 кг
l размер: 360 * 180 * 370 мм
l шум:85db
Characteristics:
<улей>
l the advantage of this product is its stable performance, pressure can be set.
l the product is equipped with a rubber high pressure hose for universal use.
l the product provided for exceptional quality and convenience.
l The перекрыл twin cylinder two-stage compression used by this product has the feature of large displacement, quick filling with air, which not only can be used for fire cylinder diving, but also can be used in car, truck, truck and other car.
L One machine serves several purposes with a wide range of applications. Машина поставляется с универсальным разъемом для быстрого подключения и зарядки, в дополнение к заполнению цилиндра, он также может быть использован для автомобилей, мотоциклов, электромобилей и других транспортных средств.
Pass:
<улей>
Leak test, Pressure vessel, Heavy Duty Pressure experiment and other industrial fields
Packing List:
<улей>
1X main machine
1X водяной насос
2x pressure release screw
1X breathing nozzle
1X водопровод
4X explosion-proof shield
5X элемент фильтра
1X set of o-rings
1X filter
Operation instruction:
<улей>
1 、 Take out the product; install a hose on the air outlet.
Note: a gasket is needed, otherwise air may leak.
2 、 Connect the 2 cold water pipes and connect them the water pump.
Note: down tube connected to the water pump is the water inlet; a sinking pump is used
in this product. Водяной насос должен быть погружен в воду перед использованием.
3 、 Install the pressure relief Valve bolt; The relief Valve bolt is installed in the relief hole under The hose. A continuous blowdown valve is installed on
discharge outlet of the first air chamber block.
4 、 Immerse the water pump in water and turn on the power.
5 、 Connect the container must be inflated, make sure the connection is correct.
6 、 Tighten The Purge valve and relief Valve bolts.
7 、 Turn on the power and the unit works.
Note: The water must function properly when the machine is running, otherwise the product may be поврежденных due to overheating and even personal injury may result.
8 、 After filling is completed, please loosen the safety valve screw first and then disconnect the power supply, thus avoid the high pressure air люфт caused by sudden power failure, which can extend the product life, and also release the high pressure air in the machine.
ATTENTION:
<улей>
1 、 Please add lubricating oil before using the machine. - Гидравлическое масло нет. 46 wear-resistant. Не забудьте налить смазочное масло в компрессор до начала;
2 、 During operation, if the machine vibrates после выступления, please add a pad or towel under the compressor;
3 、 When the compressor is running, the cooling system must run at the same time;
4 、 The machine cannot work without oil, therefore pay attention to the oil level.
предупреждение: < /h2 >
<улей>
1 、 Please use the power supply according to the parameter table.
2) Если существует какой-либо unusual noise while using the product, please stop using it immediately and check the cause.
3 、 Place the product where children cannot touch.
4 、 Please Don ' t use it in a damp and flammable place.
5 、 Please not modify it arbitrarily, disassembly and repair by non-technical personnel is not allowed.
6. Пожалуйста, убедитесь, что сокет может не иметь тока больше, чем 8а до использования, в противном случае схема может быть сожжена, продукт может быть поврежден и может быть опасен из-за overload
Viber
Telegram
