POWERFUL WELDER FOR PLASTIC WEP 8858-PRODUCT SHOWN IN the PICTURE
Support for the hotair stock
шнур питания
a set of 5 nozzles in total.
round with a diameter of 7 mm
round with a diameter of 9 мм
square by 12x12 мм
+ Quick welding nozzle BUT
+ Reduction nozzle for the but nozzle
<улей>
Plastic (JOINT) - PP triangle with a base (50 grams) about 45 CM long, for welding plastics
Plastic (JOINT) - ABS triangle with a base (50 grams) about 45 CM long, for welding plastics
<улей>
Reinforcing mesh 1 шт.. with dimensions of 20x25 CM
The сварщик состояние живых характеризуется is by:
<улей>
Digitally controlled Air discharge regulation.
контроль температуры от 100 ° C до 480 ° C
светодиодный дисплей
Fast achievement of the desired temperature and high temperature stability
Fan driven by a brushless motor (high durability and надежность, quiet operation, low vibration)
Stock photo on the right
our nozzle is on the right side of the photo
please pay attention to the air outlet gap for regulation with minimum Air supply! what the competition doesn't
Set of 5 nozzles
round with a diameter of 7 mm
round with a diameter of 9 мм
square by 12x12 мм
+ Quick welding nozzle BUT
+ Reduction nozzle for the but nozzle
BUT nozzle in the photo on the right
the photos below show an example of how to set up and use the BUT nozzle-nozzle included!
The But nozzle is placed on the round nozzle with a diameter of 9 мм, which is included in the set
* no binder included
Welding with the but nozzle-an additional hole in the nozzle is provided for plastic insertion
<улей>
Welding without a but nozzle
Plastic (JOINT) - ABS triangle with a base (50 grams) about 45 CM long, for welding plastics
It is a typical материал, used for elements produced in the rotomolding technology, e.g. tanks in small fuel bases, tanks used in agriculture, tanks in sewage treatment plants
Plastic (JOINT) - PP triangle with a base (50 grams) about 45 CM long, for welding plastics
general purpose binder
Automotive
Industry
ELECTRONICS HOME APPLIANCES
Working temperature (depends on the performance of the welder and welding conditions) - 260-330 ° c
Reinforcing mesh - 1 PIECE
Ydimensions
<улей>
Dimension: 20x25 см
размер сетки: 1.6 мм
Wire Thickness: 0.4 мм
материал: гальванизированный
The welding machine comes with an electronic plastic welding guide. это знакомит вас с проблемами сварки пластика в легком пути и делает его легче начать работу с устройством. после покупки, пожалуйста, свяжитесь с нами по электронной почте, чтобы отправить вам руководство. Thank you.
the photo shows the construction of the heating element
Heater with a thick wire, wound on the frame-thanks to this, it is not possible to accidentally short-circuit The wire by a gentle tap
Calculation of the profitability of welding
Typically, the price of the service is calculated based on the type of crack:
<улей>
difficult fracture - до 2/10 мм
<улей>
средняя трещина составляет 1.5 PLN / 10 мм
<улей>
- до 1/10 мм
<улей>
other cases of repair of plastic elements according to individual arrangements
for example: in case of a break of a moderately difficult bumper with a length of 70 cm, the purchase is returned after the repair of 2-3 bumpers.
Viber
Telegram
