ERT-33 - MERCEDES OM642 3.0 CDI КОМПЛЕКТ ДЛЯ РЕМОНТА

- 1 Piece: Teflon grease

наиболее общий сбой, связанный с intake manifold in Mercedes-Benz OM642 V6 engines is the destruction of the plastic lever that activates The intake flap system. The main source of the problem is the материал (пластик) from which the lever responsible for the movement of the flaps is made. The Engine control module responsible for the codes for the intake manifold Air flaps and the lever control system receives information about the problems. Over time, this less durable plastic cannot withstand constant cycles of heat and mechanical stress, therefore the weakening of the материал leads to the неизбежное failure.

One of the disadvantages of the OM 642M diesel engine are the поврежденных intake manifold swirl flaps, which stop working due to wear of the клешни securing the flap handle with the guide at the junction of the lever with the flaps !!!

the cause of wear is the material from which the swirl flap Drive system is made - made of plastic (non-durable plastic).

в течение долгого времени, соединительные точки рычага и демпфера изнашиваются, что приводит к нарушению вихревых клапанов в манифолде.

решение этой проблемы может быть только заменой intake manifold, и manifold costs ABOUT PLN 2,500 ... Осознание факта, что оба манифольда (правые и левые) должны быть заменены, это очень expensive solution.

наш комплект посвящен 2 коллекторам: левая и правая стороны !!!

The Aluminum inlet Manifold repair kit is the only solution that solves all these problems during the first and your last repair ...

... но с нашим новым, специально разработанным ремонтом, вы избежите этого и не будете долго заменять входную дверь !!!

Когда вы покупаете used collector, unfortunately you will not solve the проблема, because the clips and the tendon are 99% equally worn !!!

SYMPTOMS of BAD FUNCTIONING FLaps:

1) Low efficiency (loss of torque and therefore Fuel savings)

2) Loss of collector operation

3) "Check Engine Light" message

4) задержка ускорения

You can easily diagnose the above problems by removing the engine hood and checking the condition of the manifold and levers from the front.

Most likely, if you have the above symptoms, The plastic lever has broken for half or "years" or is loose at the link between the cable and the clips !!!

решение:

our intake manifold lever is made of aluminum and will never break !!!

We propose A way out of this situation - a repair kit for Mercedes swirl flap connectors (Made of aluminum, which significantly extends their service life). With the repair kit, you completely solve this проблема, restore the operation of the swirl flap system and, moreover, save your budget and time !!!

APPLICATION:

OM642 / OM642M-3.0 3.2 CDI V6 / 3.0 CRD дизельных двигателей

- MERCEDES W164 ML

- MERCEDES W166 ML

- MERCEDES X164 GL

- MERCEDES X166 GL

- MERCEDES W211 E

- MERCEDES W212 E

- MERCEDES W207 E

- MERCEDES W251 R

- MERCEDES 216 CL

- MERCEDES W221 S

- MERCEDES VITO VIANO W639

- MERCEDES SPRINTER 906 W906

- MERCEDES W219 CLS

- MERCEDES W209 CLK

- JEEP GRAND CHEROKEE WK / WH 3.0 CRD

- JEEP COMMANDER XK / XH 3.0 CRD

- CHRYSLER 300C 3.0 CRD

- DODGE FREIGHTLINER 3.0

FOR INDUCTION MANIFOLDS WITH OE NUMBERS: A6420905437; A6420907737; 6420903237; 6420905037; 6420905437; 6420907737; A6420905037; A6420907737; A6420903237; A6420905437; A6420903237; A6420905037

ONLY ALUMINUM TENDONS AND NEW CLIPS TOGETHER WITH STEERING TENDONS GIVE YOU CERTAIN THAT the probably WILL not REPEAT !!!

please VIEW ON THE YOUTUBE.COM VIDEO AFTER ENTERING "Mercedes 320 CDI Intake flaps fail"

CRACKED PLASTIC TENDON AND LOOSE AND "WORKED" COLLECTOR FIXING CLIPS:

THE CABLES CONTROLLING THE MECHANISM, THE JOINTS HAVE MADE VERY OFTEN !!! AS the ONLY WE OFFER a KIT WITH PLASTIC BANDS !!!

LOCATION OF LEVER ON INDUCTION MANIFOLD:

REPLACEMENT INSTRUCTIONS:

ремонт с нашим комплектом не является сложной процедурой, но это должно быть сделано на этапах и очень тщательно, потому что все элементы, включенные в комплект, должны быть установлены с высокой точностью.

1. Thoroughly clean the places under the old guide and its hooks (rinse with gasoline and use a needle to clean all страхования депозитов).

2.Lubricate The hooks with a thin layer of grease (a small amount is enough - GREASE is ADDED WITH the KIT).

3. Put the Aluminum guide in place.

4. добавить некоторые смазки в отверстия в алюминиевом руководстве.

5. установить новые клипы. FINISHED !!!