ЗАРЯДНОЕ УСТРОЙСТВО 6V 12V 24V 10A купить на Avtoex из Польши в Украине - Львов, Одесса, Запорожье, Тернополь, Харьков, Днепр, Винница, Суммы, Николаев, Черновцы, Мариуполь.

Дополнительная информация
Состояние	Новый

CHARGER BATTERY CHARGER 6V 12V 24V 10A

✅ TECHNICAL DATA

<улей>

Brand: POWERMAT

модель: PM-PM-60B

номинальное напряжение: 230 В / 50 Гц

supported Battery voltages: 6V / 8V / 12V / 14V / 16v / 24V (Pulse dynamic)

Voltage identification for 12V: 8V - 14.5 V

Voltage identification for 24V: 18v-29v

battery capacity 12V / 24V: 3ah-150ah

зарядный ток: 0a-10A

процесс зарядки: 8-step (intelligent or fast)

рабочая температура: -30 ° C - 50 ° C

efficiency: 98%

supports batteries: VRLA, WET, GEL, EFB, AGM

built - in Fan controlled by MCU

чистый вес: 0.95 кг

длина шнура питания: 136 см

length of "+" and "-" wires: 120см

MCU (Microcontroller Unit) technology; PWM (Pulse-Width Modulation), LCD.

✅Intelligent operating modes

Advantages of microprocessor control

<улей>

Constant Voltage: Use a DC voltage to charge the battery by checking that the charge current is not too high by reducing it during the process.

постоянный ток : Means the battery voltage is lower than the set voltage of the charger, but the charger will maintain a constant current to charge the battery.

Trickle Charge Modulation: Когда battery voltage approaches The rated voltage and the charging current is already low to set current, it will switch to floating charge modulation. Это означает, что батарея заряжена, но она постоянно проверяется на падение напряжения и автоматически заряжается с помощью переменного тока.

Floating Charge Modulation: This mode will keep the battery fully charged.

✅8-step charging

<улей>

STAGE 1: DIAGNOSTICS : analysis of the battery, its state of charge and correctness of connections between the battery and the charger.

STEP 2: DESULFATE : recognition of a sulphated battery, low voltage, high тока импульсный charging allows the sulphate to be removed from the plates of the battery, thus restoring its original capacity.

STAGE 3: ANALYSIS : checking whether the battery is not повреждены and whether it can accept the charging current - prevents charging the поврежденных battery.

STAGE 4: SOFT START : if the battery is not повреждены, it starts charging with a relatively low current (about 15%), gradually increasing its value.

STEP 5: BASIC CHARGING : charging with the maximum current of constant intensity with a value automatically adjusted depending on the battery charge status, until reaching 80% of the battery capacity.

STEP 6: FINAL CHARGE : charging with decreasing current and constant voltage until reaching 100% Battery capacity.

STEP 7: ANALYSIS : Approximately 2 minutes Battery charge test - If the battery charge does not drop after stopping charging, the charging process is complete.

STEP 8: ПУЛЬСИРУЯ : monitor battery voltage and maintain optimal charge at 95-100% capacity through charging current pulses.

MCU (microprocessor control)

✅Security features

<улей>

Surge protection - protection is activated when the charging voltage setting other than the detected parameter.

Battery Diagnostic Feature - The charger continuously monitors the condition of the battery.

Overheating protection: When the charger temperature exceeds 150 ° C, the charger will stop charging. Когда температура снижается до 80 ° C или зарядное устройство отключается за 10 минут, батарея может заряжаться снова после этого времени.

Short-circuit protection: It will automatically stop when a short circuit occurs in the circuit. Это приведет к длинному Гудку. Просто подключи зарядное устройство, и оно будет заряжаться автоматически.

Reverse-connecting protection: If the terminals (+/-) are connected the other way around by mistake, the charger will alert you with intermittent long beeps. After the terminals are properly connected, recharging will take place.

✅Modern PWM charging technology with MCU

The PM-PM-60B rectifier by Powermat is the first battery charger on the market with a microprocessor control and control system in PWM technology with the possibility of charging batteries up to 24V and the possibility of choosing non-standard types of battery voltages, which will толковейше and specifically select the appropriate parameters, making your discharged and как долго не слушал battery will be regenerated.

Intelligent battery reconditioning is done by continuous system test and charging switching in 4 modes ( Constant Voltage; Constant Current; Trickle Charge Modulation; Floating Charge Modulation ).

Charging in intelligent (SMART) or fast (FAST) mode does not need your attention, because all the programs controlling the charging process have been carefully designed for the appropriate types of batteries and their rated voltages in order to bring them to perfect condition as accurately as possible. Pulse-Width Modulation - is a method of adjusting the current or voltage signal, with a constant amplitude and frequency, consisting in changing the duty cycle of the signal. PWM system powers the device directly or through a low-pass filter smoothing changes in electric current and voltage.

Displaying The charging parameters позволяет дополнительно проверить состояние вашей батареи. The large display informs about the current current, charging mode and the current voltage of the battery. Кроме того, состояние заряда как процент может быть обсервировано.

Very high Charging efficiency at positive temperatures. Благодаря расширенному контролю за зарядными процессами, эффективность выпрямителя составляет 98%, что делает его несовместимым с традиционными типами выпрямителей без этого типа технологии.