PLASTIC WELDER + NOZZLES + BOOT + PLASTIC + MESH
+ длинный кабель 1m
!! BUT nozzle facilitates The Binder feeding process-it is recommended for professional plastic welders!
PERFECT Starter KIT !!! VALID WHILE STOCKS LAST - CHANCE !!!
Retail offer!
<улей>
The BEST PLASTIC WELDER WEP 8858-I PRODUCT SHOWN IN the PICTURE-OTHER PRODUCERS IMITATE US
X4 NOZZLES with the but nozzle
PLASTIC ( WELD ) - 2х100 grams - description below
NET
улей>
технические характеристики:
<улей>
Digitally controlled Air discharge regulation.Ли>
Air flow regulation up - 22 л / мин макс.
контроль температуры от 100 ° C до 480 ° C
светодиодный дисплей
Air flow source:fan
Air flow: up составляет 120 л / мин
Blowing type: Soft start brushless fan
Cable length:1m
Size: 305x60x60 [length, height width]
Strong heater made of thick wire mounted on a frame (greater strength and durability of the heating element)
улей>
SET CONTAINS:
<улей>
WEP 8858-я < /B> welder
Support for the hotair stock
улей>
a set of 5 nozzles in total
- round with a diameter of 7 mm
- round with a diameter of 9 mm
- площадь 12x12 мм
- + Quick welding nozzle BUT
- + Reduction nozzle for the but nozzle
<улей>
Plastic (JOINT) - PP triangle with a base (100 grams) about 45 CM long, for welding plastics
Plastic (JOINT) - ABS triangle with a base (100 grams) about 45 CM long, for welding plastics
Reinforcing mesh 1 шт.. with dimensions of 20x25 CM
улей>
<улей>
BUT nozzle in the photo on the right
the photos below show an example of how to set up and use the BUT nozzle-nozzle included!
The But nozzle is placed on the round nozzle with a diameter of 9 мм, which is included in the set
улей><улей>
Welding with the but nozzle-an additional hole in the nozzle is provided for plastic insertion
улей><улей>
Welding without a but nozzle
улей><улей>
Plastic (JOINT) - ABS triangle with a base (100 grams) about 45 CM long, for welding plastics
It is a typical материал, used for elements produced in the rotomolding technology, e.g. tanks in small fuel bases, tanks used in agriculture, tanks in sewage treatment plants
Plastic (JOINT) - PP triangle with a base (100 grams) about 45 CM long, for welding plastics
general purpose binder
Automotive
Industry
ELECTRONICS HOME APPLIANCES
Working temperature (depends on the performance of the welder and welding conditions) - 260-330 ° c
улей><улей>
Reinforcing mesh - 1 PIECE
улей>
Ydimensions
<улей>
Dimension: 20x25 см
размер сетки: 1.6 мм
Wire Thickness: 0.4 мм
материал: гальванизированный
улей>
<улей>
сварочная машина поставляется с электронным пластиковым сварочным гидом. это знакомит вас с проблемами сварки пластика в легком пути и делает его легче начать работу с устройством. после покупки, пожалуйста, свяжитесь с нами по электронной почте, чтобы отправить вам руководство. Thank you.
улей><улей>
the photo shows the construction of the heating element
Heater with a thick wire, wound on the frame-thanks to this, it is not possible to accidentally short-circuit The wire by a gentle tap
улей><улей>
the photo shows the construction of a heating element covered with mica
улей>Calculation of the profitability of welding
Typically, the price of the service is calculated based on the type of crack:
<улей>
difficult fracture - до 2/10 мм
улей>
<улей>
средняя трещина составляет 1.5 PLN / 10 мм
улей>
<улей>
- до 1/10 мм
улей>
<улей>
other cases of repair of plastic elements according to individual arrangements
улей>
for example: in case of a break of a moderately difficult bumper with a length of 70 cm, the purchase is returned after the repair of 2-3 bumpers.п>