PP triangle with a base of 4 mm, length approx. 45 см (3 шт. )
ABS треугольник с базой 4 мм length approx 45 см (3 шт. )
PP strip 8mm wide, about 45cm long (3 pcs. )
ABS strip, 8 mm wide, approx.45 см long (3 шт. )
улей>
Strengthening mesh 2 pcs. with dimensions of 20x25 см
Plastic сварщик WEP 8858 characteristics:
<улей>
Digitally controlled Air discharge regulation.Ли>
Air flow regulation up - 22 л / мин макс.
контроль температуры от 100 ° C до 480 ° C
Power энергопотреблением: 650 ВТ
светодиодный дисплей
Air flow source:fan
Air flow: up составляет 120 л / мин
Blowing type: Soft start brushless fan
Cable length:1m
Size: 305x60x60 [length, height width]
Strong heater made of thick wire mounted on a frame (greater strength and durability of the heating element)
BUT nozzle in the photo on the right
the photos below show an example of how to set up and use the BUT nozzle-nozzle included!
The But nozzle is placed on the round nozzle with a diameter of 9 мм, which is included in the set
Welding with the but nozzle-an additional hole in the nozzle is provided for plastic insertion
Welding without a but nozzle
The iron nozzle is pictured on the right
Used for
<улей>
Оперение reinforcing mesh,
smoothing The weld,
улей>
This saves you time on the final processing of the weld.
Nozzle Iron dimensions
<улей>
Fits welders with an outlet diameter of 22 мм
Working surface :triangle with sides 25x20x25 мм
Binder PP Profile strip - 3 pcs.
ABS binder Profile strip - 3 шт.
Binder PP треугольник профиль - 3 шт.
ABS binder треугольник профиль - 3 шт.
улей>
технические характеристики:
<улей>
Length: one piece about 45 см
улей>
Profiles
general purpose binder
<улей>
Automotive
Industry
ELECTRONICS HOME APPLIANCES
Working temperature (depends on the performance of the welder and welding conditions) - 260-330 ° c
Ширина ремня - 8 мм
a triangle with a base - 4 мм
Reinforcing mesh - 2 PIECES, dimensions: 20x25 см
The welding machine comes with an electronic plastic welding guide. Это знакомит вас с проблемами сварки пластика в легком пути и делает его легче начать работу с устройством. После покупки, пожалуйста, свяжитесь с нами по электронной почте, чтобы отправить вам руководство. Thank you.
the photo shows the construction of the heating element
Heater with a thick wire, wound on the frame-thanks to this, it is not possible to accidentally short-circuit The wire by a gentle tap
the photo shows the construction of a heating element covered with mica
Calculation of the profitability of welding
Typically, the price of the service is calculated based on the type of crack:
<улей>
difficult fracture - до 2/10 мм
улей>
<улей>
средняя трещина составляет 1.5 PLN / 10 мм
улей>
<улей>
- до 1/10 мм
улей>
<улей>
other cases of repair of plastic elements according to individual arrangements
улей>
for example: in case of a break of a moderately difficult bumper with a length of 70 cm, the purchase is returned after the repair of 2-3 bumpers.