Operating Instructions:
Setting the full and cur-off voltage
Set the full voltag:
Step 1: In the normal display interface(like fig. 1), long press The button until the LCD screen display the interface like fig. 2, then release the button
Step 2: SET character blink present it is the setting status of full / cut-off voltage, long press The button until the LCD screen display the interface like fig. 3, then release the button
Step 3: At this time, the battery symbol display full Grid energy means the full voltage setting status, factory default the full voltage is 020.0 V, the numerical code circulation flashing from the low bit to the high bit show that the current setting digit, short press to set the digit;please pay attention that, as the full voltage setting value has 4 digit, but the numerical code has only 3 digit, so the setting is divided into two parts: low bit (фіг. 3) високий біт (рис. 4). For example, the default full voltage is 020.0 V, then the display state is 20.0 V to 020v low and high cyclic switching display. Якщо вам потрібно встановити повну напругу 199.0 V, то будь ласка, встановіть низький біт на 99.0 V, коли цикл досягне високого біт, він буде відображати 099v, і тільки найвищий нульовий біт, щоб підказати, що він може бути встановлений. 199v представляє повну напругу 199.0 V.
Set the Cut-off voltage:
Step 1: After you set the full voltage, loner press The button until LCD shows the interface of Fig. 5, then release the button;
Step 2: At this time, the battery symbol shows the zero-grid to indicate the cut-off voltage setting state, the default cut-off voltage is 016.0 V, The setting method is the as above;the cut-off voltage is 0.8 times of the full voltage by default, after setting the full voltage, the cut-off voltage is automatically generated in the relationship of 0.8 times; otherwise, you can reset it;
After all the above settings are completed, long press The button until the settings are saved and exit the setting status, restore the normal Display interface.е>
Clear the Energy
Step 1: In the normal display interface, long press The button until the LCD shows the interface of Figure 2, then release the button, short press The button again switch to the interface to Figure 9, it indicates that this state is The clearing energy setting state.е>
Step 2: Longer press The button until the data has been cleared and exit the setting status, restore the normal Display interface.е>
Clear the capacity
Step 1: In the normal display interface, long press The button until the LCD shows the interface of Figure 2, then release the button, short press The button again switch the interface to Figure 10, it indicates that this state is The clearing capacity setting state .е>
Step 2: Longer press The button until the data has been cleared and exit the setting status, restore the normal Display interface.е>
Clear the running time
Step 1: In the normal display interface, long press The button until the LCD shows the interface of Figure 2, then release the button, short press The button again switch to the interface to Figure 11, it indicates that this state is The clearing running time setting state.е>
Step 2: Longer press The button until the data has been cleared and exit the setting status, restore the normal Display interface.е>
робочий режим
This meter has two modes: normal display mode and dormant mode. У нормальному режимі відображення, натисніть кнопку,щоб увійти в дормантний режим, в порядку зменшення всієї машини споживання енергії, підсвічування і РК-дисплей буде вимкнений в дормантном режимі. У dormant mode, short press the button will switch to the normal display mode.е>
Power consumption
нормальний робочий стан: 0.03-1.2 в
стан сну: 0.5 МВт-0.5 Вт
споживання енергії пов'язане з випробувальним значенням напруги, більш високою напругою, більшою потужністю
consumption.е>
робоча температура: -20℃ - 60℃