PLASTIC WELDER WEP 852D + + NOZZLES ПЛАСТИКОВАЯ СЕТКА

SET096

On this listing, you are buying:

Reinforcing mesh - 1 piece, size 20x25 [см]

Set of 5 nozzles:

1. Round nozzle with a diameter of 5 мм
2. Round nozzle with a diameter of 7 mm
3. Round nozzle with a diameter of 9 мм
4. + Quick welding nozzle BUT
5. + Reduction nozzle for the but nozzle

Plastic welding tutorial

The WEP 852D + сварщик состояние живых характеризуется is by:

• BUT nozzle in the photo on the right
• the photos below show an example of how to set up and use the BUT nozzle-nozzle included!
• The But nozzle is placed on the round nozzle with a diameter of 9 мм, which is included in the set

Welding with the BUT nozzle - an additional hole in the nozzle is provided for plastic insertion

Welding without a BUT nozzle

• Plastic (JOINT) - ABS triangle with a base (100 grams) about 45 CM long, for welding plastics
• It is a typical материал, used for elements produced in the rotomolding technology, e.g. tanks in small fuel bases, tanks used in agriculture, tanks in sewage treatment plants
• Plastic (JOINT) - PP triangle with a base (100 grams) about 45 CM long, for welding plastics
• general purpose binder
• Automotive
• Industry
• ELECTRONICS HOME APPLIANCES
• Working temperature (depends on the performance of the welder and welding conditions) - 260-330 ° c

Reinforcing mesh for welding plastic.

Perfect for recreating missing elements such as:

• The welding machine comes with an electronic plastic welding guide
• это знакомит вас с вопросами сварки пластмасс в легком пути и делает его легче начать работу с устройством
• после покупки, пожалуйста, свяжитесь с нами по электронной почте, чтобы отправить вам руководство
• Спасибо

The WEP 852D + сварщик for plastic is a very useful device for everyone who needs to connect plastic elements in a short time. У вельдера был контроль температуры и сила выдуваемого воздуха. Welder additionally equipped with an automatic cooling system after work. Это эффективно расширяет жизнь теплового элемента.

It is most often used for welding elements such as:

You can use the welder to repair electrical installations: by shrinking the sleeves.

Calculation of the profitability of welding

типично, the price of the service is calculated based on the type of crack:

crack difficult до 2 / 10мм рублей

средняя трещина, до 1.5 PLN / 10mm

взломать легко до 1 / 10мм рублей

other cases of repair of plastic elements according to individual arrangements

улей>

for example: when a bumper cracks 70 cm long, with a medium-difficult crack, the purchase is returned after 2-3 bumpers are repaired.

• Rubber feet
• Red Shipping bolts , please unscrew before using the device!

• a tipped stock marked 907A with a power of 60W 5pin

Connecting the heating element

The blue andred wires are connected to the Temperature sensor (Blue is минус) (Red is plus)

2 leads in a transparent (transparent) sleeve are used to connect the heater

• the photo shows the construction of the heating element
• heater with a thick wire is wound on the frame-thanks to this, it is not possible to accidentally short-circuit The wire by gentle tapping
улей>

Connecting the heating элемент

• Blue and red wires are for thermocouple connection (Blue is negative) (Red is positive)
• The red wires are used to connect the heater