Characteristics:
High-capacity flash
Acro
предназначен для обеспечения удивительной производительности полета, основанной на проверенных и проверенных датчиках
While providing unmatched and in a small and ultra-lightweight form factor with a Next-generation processor.
Flight Performance: SP Racing F3 relies on tried and tested software, processor and sensor technology to make planes fly like they on rails.
Spacerf3 runs Clean Flight, который может быть сконфигурирован, чтобы соответствовать вашим потребностям, используя кросс-платформенный графический интерфейс (Windows / OSX / Linux).
Flight logging. Durable black box Flight log recorder with high capacity-optimize tuning and see setup results without the guesswork.
Developer-friendly debug port (SWD) and boot Mode selection, unbreakable bootloader.
Extensive RC receiver support. Supports SBUS, SUMH, SUMD, Spektrum1024 / 2048, XBUS, PPM, PWM receivers.
мониторинг батареи. Battery monitoring ports for voltage and current.
I2C port always powered, perfect for external sensors or Always on OLED screen.
Small and light.
SpacerF3 has a Cortex-M4 72MHZ RAM processor with a Math CO-Processor (FPU) for efficient Flight calculations that are more done in less time.
Loop times up to 2x as fast as previous generation STM32F1 based boards.
OneShot Esc.
Full OneShot Esc support for easy PID tuning and sharper response.
Sonar support for precise hold at low altitude.
Посторонние port for audible warnings and notifications.
SpacerF3 has all the features needed for the heart of an airplane, whether you like FPV racing, акробатический flying or aerial photography, it's perfect.
It supports a variety of planes, planes, and more.
практический-легкий доступ к соединителям и припоям.
Configurable-Choose to use connector, solder pads or pins.
Crops-mount для PDB или OSD.
компактный, профессиональный, аккуратный и аккуратный.
ACRO: стандартная модель ACRO racing / flying.
программное Обеспечение:
Spacef3 runs CleanFlight Flight Control Clean-source software, which has an ever-evolving community
friendly developers and users. Быть открытым исходным кодом означает, что вы можете войти в систему как хорошо.
CleanFlight includes a detailed manual that is reviewed and maintained by The CleanFlight developers and community.
No more outdated wiki pages and second-hand information.
Make sure you refer to manual corresponding to the firmware version.
History
аппаратное обеспечение было разработано разработчиком Cleanflight Dominic Clifton, чтобы быть более способным, чем
STM32F1 based boards after hearing feedback from CleanFlight users, co-workers and top материал верха:.
Failure to comply with these warnings will void your warranty and damage your flight
контроллер.
the Соблюдать полярность at all times. Проверка и двойная проверка до применения силы.
Remove before disconnecting, connecting, or making connections.
Connect only one power source to VCC pins / not connect more than
One power source for two or more VCC pins. e. g. If you are using ESCS
then from the BEC, remove the middle red wire from all Esc connectors except one.
Warnings
OVERALL ADVICE
следуйте советам ниже, чтобы получить лучшую производительность и длительный срок с вашего контроллера полета:
применить resin / glue к strengthen JST-SH joints-helps in case of airplane crash.
the use of a housing / box for the flight controller is recommended.
Install Open-Cell foam under the pressure sensor-sandwich between FC
and frame.
DISTRIBUTE ENGINE / lower SERVICE for FURTHER WITH REMOTE SENSORS (MAGnetometer)
how it's possible.
Only install the boot pins when you need them.
it is recommended (not provided), чтобы использовать цветные PIN headers, особенно для VBAT
headers.
чтобы вы могли получить вибрацию в акселерометре / гироскопе.
Specifications:
6DoF
панель color: black
Board size: 35 x 35 x 8 мм / 1.4 x 1.4 x 0.3 inch
Net Weight: 23g
вес упаковки: 29 гPackage including:
1 х SP гоночный контроллер
1 x прямой контактный разъем
1 x looper заголовок разъем
1 х контактный разъем
1 х корпус корпуса
with some lines and bolts
Viber
Telegram
